Assemblies, R-values, and coverage,measured off the wall types.
Ruh AI measures the insulation by assembly and R-value off your wall types, priced on your own rates and signed by your estimator.
- ✓Wall, roof, and floor area in square feet by assembly and R-value
- ✓Batt, rigid, and spray foam separated, cavity and continuous distinguished
- ✓Live in about a week on Bluebeam, Procore, and Excel
The insulation bid crew.
The agents that carry an insulation set from measured takeoff to a priced, signed proposal.
From wall types to priced insulation bid, one motion.
Send the insulation set
Floor plans, wall sections, elevations, the wall type schedule, roof and floor assemblies, and the Division 07 spec, straight from the invitation. Sheet and detail classification starts immediately.
Assemblies, R-values, and area run
Wall, roof, and floor area measured in square feet by assembly and R-value, batt, rigid, and spray foam separated, and cavity insulation distinguished from continuous insulation off the wall types and sections.
Accessories and system priced
Batt, rigid board, spray foam, pipe and duct insulation, vapor barriers, firestopping, and air sealing priced on your own assemblies and history, with staging and access where the scope calls for it.
Your estimator signs
Review by confidence and coverage score, adjust the assumptions, and export into your own proposal format.
The insulation bid squeeze.
Coverage decides the year
Insulation subs bid more square footage than a small estimating room can measure by hand. Every set that sits unpriced is a job that goes to the sub who got a number out first.
The assemblies hide the margin
Square footage is the easy part. The margin hides in the continuous insulation at the slab edge and parapet, the spray foam in the rim joist, the pipe and duct wrap in the mechanical room, and the firestopping and air sealing that are easy to miss on a fast manual takeoff.
Lump-sum leaves no room to be wrong
Most insulation goes out as a lump sum. A missed continuous layer, the wrong R-value, or a light waste number does not surface in a change order. It comes straight off the crew's margin.
AI insulation takeoff and estimating, explained.
The takeoff is the bid
Insulation estimators tell us the same thing: the number is only as good as the quantities behind it, and measuring wall, roof, and floor area by assembly and R-value by hand off a PDF takes hours. When the area, the assemblies, and the linear feet of pipe and duct insulation run as one measured pass on the real wall types and sections, the same room prices more sets and keeps senior judgment on the details, the assemblies, and the R-value scope, which is where an insulation bid is actually won or lost.
Built for how assemblies are measured
Batt, rigid, and spray foam are different takeoffs, and the pipeline treats them that way. Wall, roof, and floor area is measured by assembly and R-value off the wall types and sections, cavity insulation is distinguished from continuous insulation so each prices on its own basis, and pipe and duct insulation is measured in linear feet by size and material. Vapor barriers, firestopping, and air sealing are counted and measured off the details and reconciled against the wall type schedule and the Division 07 spec. Openings are deducted so you are not paying to insulate through a window.
Priced on your book, signed by your estimator
The quantities are priced by square foot and linear foot across nine stages on your own historical rates and assemblies for the systems you install, whether that is fiberglass batt, mineral wool, rigid board, or spray foam, with staging and access carried where the scope calls for it. Every line is labeled measured, derived, or assumed with a confidence and coverage score, so a light spot in the set is visible in the review instead of buried in a lump sum. Nothing goes out until your estimator signs it, and it all runs inside your own tenant on Bluebeam, Procore, Autodesk, and Excel, live in about a week.
Insulation numbers that hold up.
Judge it on your own insulation set, not a demo.
Built to work together.
See it on your own insulation set.
A free 30 minute walkthrough on a real insulation set, no card. We run the takeoff live and you decide if you move forward.
Proof and perspective.
One useful email. No drip campaign.
Takeoff teardowns, cost data, and field notes from teams putting AI on real bids. Sent when there is something worth reading, never on a content calendar.
No spam · Unsubscribe anytime
Frequently asked questions
What insulation estimators ask before trusting an AI takeoff on a real set.
How accurate is the insulation takeoff?
Can Ruh run AI agents for insulation estimating?
Does it actually read our wall types and sections?
Can it price on our own insulation rates?
Does it fit the software we already run?
Can it give a quick budget number and a full bid?
Run your next insulation bid on Ruh.
Send one insulation set. We run the takeoff and walk you through the wall, roof, and floor area, the R-values, the spray foam, and the pipe and duct insulation on a 30 minute call. If it does not hold up against your estimator, you have lost nothing.